Tools You Need to Install a New Bathtub
Tools You Need to Install a New Bathtub
Blog Article
Right here down the page you will find a bunch of good quality tips concerning Installing A Bathtub.
Mounting a bath tub isn't specifically rocket science, however it does need solid plumbing, carpentry, as well as often, tiling skills. Replacing an old bathtub with a new one is also a moderately challenging job. If the old tub is easily easily accessible, the job can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the new tub, the task is a lot harder. In either case, the job is within a residence handyman's abilities, although you will certainly need a helper to leave the old bathtub and set in the new one. See to it you have qualified yourself for the task and also are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is better to think about using one before you start. Chances are you might need an expert plumber to make tube links.
This write-up will assist you mount a new bathtub in your bathroom if you have actually currently purchased a brand-new tub as well as do not need to alter the arrangement of your previous water supply pipes.
Your devices and material list should comprise the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be fairly troublesome as a result of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a link to the current supply pipelines.
If you require to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making certain that the washers are in area between the tap and the sink. Protect the tap in position with the manufacturer given backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind needs to be connected to the tap finishes first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Utilizing the two wood boards under its feet, position the bath tub in the called for placement. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four little points.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by checking the level and also adjusting the feet on the bathtub till the level reads degree.
To mount faucets, fit the bottom of the outermost flexible tap adapter to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Switch on the supply of water as well as examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bathtub as well as also inspect the overflow electrical outlet and also the typical outlet for leakages.
Finally, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and also securing around the tub should wait until the bathtub has actually been utilized at the very least once as this will certainly resolve it right into its last setting.
Preparing for the Installment
Firstly, the supporting framework provided with the bath should be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps system to prevent strain on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bath as well as the tiling, leading to issues with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are offered in tubes as well as cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill up the tub with water prior to securing, to allow for the motion experienced when the tub is in usage. The sealant can split fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the marketplace. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very occupied with A Step-by-Step Guide to Installing a Bathtub and I am praying you enjoyed reading the blog entry. Sharing is nice. Helping people is fun. I praise you for your time. Don't hesitate to come visit our website back soon.
Free Quote
Report this page